Skip to content

easy lock small round container - case on hex bits 31 hex. holes
3-hex-bit-round-container-case-open.jpg easy lock small round container - case on hex bits 31 hex. holes
4-hex-bit-round-container-case-with-and-without-hole-for-keychain-ring.jpg easy lock small round container - case on hex bits 31 hex. holes
5-hex-bit-round-container-case-top.jpg easy lock small round container - case on hex bits 31 hex. holes
6-hex-bit-round-container-case.jpg easy lock small round container - case on hex bits 31 hex. holes
7-example-of-thread-while-printing.png easy lock small round container - case on hex bits 31 hex. holes
8-example-of-thread-while-printing.png easy lock small round container - case on hex bits 31 hex. holes
Advertising
Share
Add to
Make
Advertising
?
Creation quality: 5/5 (1 vote)
Evaluation of on the printability, utility, level of detail, etc.
License
Usages
3D design format
1 file (ZIP) Close
  • bit holder version.zip
    • 0 tolerance/0 bottom with hole.stl
    • 0 tolerance/0 bottom.stl
    • 0 tolerance/0 lid.stl
    • -0,15/-0,15 bottom with hole.stl
    • -0,15/-0,15 bottom.stl
    • -0,15/-0,15 lid.stl
    • -0,25/-0,25 bottom with hole.stl
    • -0,25/-0,25 bottom.stl
    • -0,25/-0,25 lid.stl
    • -0,5/-0,5 bottom with hole.stl
    • -0,5/-0,5 bottom.stl
    • -0,5/-0,5 lid.stl
    • -0,7/-0,7 bottom with hole.stl
    • -0,7/-0,7 bottom.stl
    • -0,7/-0,7 lid.stl
    • description.txt
    • license.txt

Learn more about the formats
Publication date 2024-02-21 at 01:04
Design number 1802019
3d-stoirint

3d-stoirint

Certified
Issue with this design? Report a problem.

3D printer file info

3D model description

triple thread easy lock small round container-case on hex bits in 2 versions with and without hole for hanging on approx:20mm - 25mm keychain (with 5 variations of tolerances for threads) so no worries for all machines

-easiest thread to print - not very usual 6x external thread (3 external threds on outer and 3 external threads on inner body)with a large pitch angle
-with 5 different options of tolerances for threads.: 0, -0.15mm, -0.25mm, -0.5mm, -0.7mm
-the maximum need to turn the lid for locking corresponds to 180 degrees from any point around the perimeter of the lid
-31 hexagonal holes for bit storage for 6,35x25mm hexagonal screwdriver bits (7mm hexagonal holes / 27mm max height)

ready to use from printer bed
no needed

recommended print -0,15 if your printer is well set up you should be fine
-0,15 means toleration between threads of outer and inner body - they are not usual and all threads are external
tolerance for the hex bit is same on all including containers -0,65mm wich means 7mm hexagonal holes
due to the locking design of this box, I recommend tightening it strongly but with sensitivity to ensure sufficient between the walls of the threads when closing - you will immediately find out what I mean with the first piece

-0,5 tolerance is ridiculously high tested with 0,8 nozzle the thread was loose but still functional
-if you need this or a larger tolerance range, because of any geometrical errors your printer is definitely not in good condition and probably diverges between the X and Y axes means they are not in right angle (90degrees)-

-!!!-extra fit version is challenge print-!!! if you consider the way fdm printers works it should move in small triangles when printing thread and that will cause sharp edges all over thread this edges will go off in first few rotation againts the wall of other thread
these sharp edges are also the same lenght as + toleration on this print so if you sand them away (threads are same lenght so sand outer and inner thread same ammount ) you will archieve the best posible fit
or if you printer is very well maintrained you should be fine with this tolerance to insert inner to outer body of container and rub it againts walls of other thread (you will have to use force to do so basicali you will be sanding the sharp edges away) with this you will get the best toleration possible (this can be done with pla only - other materials like abs/petg need to be sanded)
!!!print extra fit only if you think your printer is one of the best printers around!!!-

everyone should be fine with -0,15 and -0,25 tolerances. if your not, maintenance your printer immediately

Enjoy.!

3D printing settings

wall loops .: 2+
infill density.: 15%+
print without s
recommended.: -0,15 or -0,25

Categories

Tool holders & boxes

Tags

Advertising

Would you like to Cults?

You like Cults and you want to help us continue the adventure independently? Please note that we are a small team of 4 people, therefore it is very simple to us to maintain the activity and create future developments. Here are 3 solutions accessible to all:

  • ADVERTISING: Disable your ad blocker.
  • DONATE: Make a donation via Ko-Fi πŸ’œ.
  • WORD OF MOUTH: Invite your friends to come, discover the platform and the magnificent 3D files shared by the community!

Sharing and ing on Cults3D guarantees that designs remain in makers community hands! And not in the hands of the 3D printing or software giants who own the competing platforms and exploit the designs for their own commercial interests.

Cults3D is an independent, self-financed site that is not able to any investor or brand. Almost all of the site’s revenues are paid back to the platform’s makers. The content published on the site serves only the interests of its authors and not those of 3D printer brands who also wish to control the 3D modeling market.