Skip to content

Fogger / Nebulizer / Humidifier Terrarium ultrasonic Nebuliser / Humidifier

Advertising
Share
Add to
Make
Advertising
?
Creation quality: 5/5 (1 vote)
Evaluation of on the printability, utility, level of detail, etc.
License
3D design format
7 files (STL) Close
  • Fogger_Ausstroemer.stl
  • Fogger_Body.stl
  • Fogger_Deckel.stl
  • Fogger_Deckel_Auslauf.stl
  • Fogger_Deckel_Auslauf_Mutter.stl
  • Fogger_Sockel_Auslass.stl
  • Fogger_Sockel_Vorrat.stl

Learn more about the formats
Publication date 2022-04-21 at 23:02
?
Published to Thingiverse on: 2022-04-21 at 07:03
Design number 701381
rolfmobil

rolfmobil

Certified
Issue with this design? Report a problem.

3D printer file info

3D model description

Fogger / Nebulizer / Humidifier Terrarium

Completely new design.

As these work together with 240V, safety extra-low voltage (24V) and water:

==> Reproduction and operation at your own risk!

I accept no responsibility for accidents, defects or other unforeseen effects!<==

  • Pay attention to cable management.

  • Fogger and fan work with 24V, the power supply unit supplies both components.

  • The fogger is activated by a WIFI switch behind an FHEM installation (home automation) at time intervals for short periods of time. Using rules in FHEM or TASMOTA, the humidity can also be controlled automatically in conjunction with a humidity meter (e.g. https://www.amazon.de/AZDelivery-BMP180-Barometrischer-Sensor-Luftdruck/dp/B07FRW7YTK).

Findings:

  • A larger pipe for the mist discharge is essential for the amount of volume flow discharged.

  • Unusable without forced ventilation.

  • The cross-section of the drain in the storage tank must not be too small, otherwise the cohesive forces will be too great and no water will run off.

  • The attached STL file for a jam jar *) did not work satisfactorily in the end, but can certainly be made functional with a little silicone.

  • The solution of drilling a hole in the lid of any jar works well, with the aid of a sealing ring.

Components:

Fogger:

https://www.amazon.de/gp/product/B089LDS24S (example)

350ml/h plus water droplets running through the pipe...

Fan / Fan:

https://www.amazon.de/L%C3%BCfter-40x40x10mm-27dBA-Sunon-KDE2404PFV2-11AB

*)

Reservoire. Jam jar, "Bonne Maman", strawberry :-), 77.60 mm outside diameter

Please also note my designs on https://cults3d.sitegames.net/en/s/rolfmobil/creations

under the same name (rolfmobil)...

Fogger / Nebulizer / Humidifier Terrarium

Design completely new.

As here work together with 240V, protective low voltage (24V) and water:

==> The reproduction and operation is at your own risk!

I take no responsibility for accidents, defects or other unforeseen effects!<==

  • Attention to cable management.

  • Fogger and fan work with 24V, the power supply unit supplies both components.

  • The fogger is activated by a WIFI switch behind a FHEM installation (home automation) at time intervals for short periods of time. By means of rules in FHEM or TASMOTA, the air humidity can also be controlled automatically in conjunction with a humidity meter (e.g. https://www.amazon.de/AZDelivery-BMP180-Barometrischer-Sensor-Luftdruck/dp/B07FRW7YTK).

Findings:

  • A larger pipe for the fog outlet is essential for the amount of volume flow delivered.

  • Unusable without forced ventilation.

  • The cross-section of the drain in the reservoir must not be too small, otherwise the cohesive forces are too great and no water will run down.

  • The attached STL file for a jam jar *) did not work satisfactorily in the end, but can certainly be made functional with some silicone.

  • The solution of drilling a hole in the lid of any jar works well, with the aid of a sealing ring.

components:

Fogger:

https://www.amazon.de/gp/product/B089LDS24S (example)

350ml/h plus water drops running through the tube...

Fan / Fan:

https://www.amazon.de/L%C3%BCfter-40x40x10mm-27dBA-Sunon-KDE2404PFV2-11AB

*)

Reservoir. Jam jar, "Bonne Maman", strawberry :-), 77.60 mm outer diameter

Please also have a look at my designs on https://cults3d.sitegames.net/en/s/rolfmobil/creations

under the same name (rolfmobil)...

3D printing settings

-

Categories

Pets

Tags

Advertising

Page translated by automatic translation. See the original version.

Would you like to Cults?

You like Cults and you want to help us continue the adventure independently? Please note that we are a small team of 4 people, therefore it is very simple to us to maintain the activity and create future developments. Here are 3 solutions accessible to all:

  • ADVERTISING: Disable your ad blocker.
  • DONATE: Make a donation via Ko-Fi 💜.
  • WORD OF MOUTH: Invite your friends to come, discover the platform and the magnificent 3D files shared by the community!

Sharing and ing on Cults3D guarantees that designs remain in makers community hands! And not in the hands of the 3D printing or software giants who own the competing platforms and exploit the designs for their own commercial interests.

Cults3D is an independent, self-financed site that is not able to any investor or brand. Almost all of the site’s revenues are paid back to the platform’s makers. The content published on the site serves only the interests of its authors and not those of 3D printer brands who also wish to control the 3D modeling market.