Kill Team 2024 - All-In-One Conversion Kit

This free (you can tip me if you want to!) conversion kit combines your individually purchased stand-alone components into a glorious all-in-one kit. It's the perfect solution for your next tournament or games night at your local club.

This Conversion Kit contains:
- A lid/cover that doubles as a generous dice tray. It has enough clearance over the upper tray to (optionally) line the bottom with felt, for that extra-luxurious feel.
- An Upper Tray, which holds the solo/lite version of the Equipment Holder*, the 40mm deep version of the Approved Ops Card Holder*, and a central dice container that holds sixteen 16mm dice (or twenty-two 12mm dice).
- A Lower Tray, which holds a Kill Team Score Tracker* and four of my standard-sized inserts for token holders/wound trackers* etc.
- An 8mm Spacing Layer that provides a buffer between multiple lower trays, allowing you to remove each token holder/drawer more easily.
- An 8mm Bottom Lift Plate. This works the same as the spacing layer but doesn't contain a solid floor (saves filament). The lift plate enables you to remove the token holders/drawers with your kit resting directly on the table. If you're unsure whether you might want to add extra drawers in the future, then add the spacing layer to the bottom of your kit instead of the lift plate.
- A "Kill Team Kit" Logo, to top it all off.

Optional components:
- you can replace the Kill Team Score Tracker with a slimline container for additional dice, laser pointers etc.
- this includes a generic empty drawer, which fits the lower tray and can be used to hold additional dice, laser pointers etc.

Note: You can attach as many lower trays as you like, essentially adding an additional four carrying slots for inserts (plus another slimline container) for each lower tray. An 8mm spacing layer is included

• This is a free conversion kit only. The individual components that it holds are sold separately, as shown below.

Wound Trackers

Team tokens holders: see my Kill Team 2024 collection

UPDATES
8th March, 2025: Generic draw, and score tracker outer shell now use 5mm x 2mm magnets.

DIMENSIONS
**Note: This is a large print, and requires a print bed capable of printing 220mm in either the X to Y dimension.
Width: 154mm
Length: 220mm
Height: Variable (Largest Individual Piece is 44mm high)

MAGNET REQUIREMENTS
The lower tray requires a number of magnets to keep the various inserts from falling out. I strongly recommend using 2mm x 5mm magnets for the lower tray, as this will provide additional security when carrying the tray around. If you only have 1mm x 5mm magnets don't stress, a 1mm magnet version of the lower tray is also included. Alternatively, you can find printable 1mm thick "magnet lifters" here (https://cults3d.sitegames.net/en/3d-model/game/alternative-token-holder-covers-and-magnet-lifters), which you can glue inside the 2mm-deep hole first, and then glue your magnet on top of that.
- Lower Tray: 10 round 2mm x 5mm magnets (or 1mm x 5mm magnets).
- Generic Drawer: 2 round 2mm x 5mm magnets
- Score Tracker Outer Shell (replacement): 2 round 2mm x 5mm magnets

PRINT SETTINGS
Cover (print this upside down)
Layer height: 0.2mm
Nozzle Size: 0.4mm
s: Yes - The recess for the logo will be face-down towards the build plate, so using s in this area will ensure there is no filament sag and will allow the logo to be fitted neatly.
Infill: 15% Grid
Ironing: None

Logo
Layer height: 0.2mm
Nozzle Size: 0.4mm
s: No
Ironing: All top surfaces, spacing 0.2mm (gives a beautiful smooth finish)
Note: For most single-head printers you can achieve the two-colour effect by adding a PAUSE (or equivalent) command into your g-code, immediately before the start of layer 4 (height 0.8mm) and changing the filament to an alternate colour.

All other components
Layer height: 0.2mm
Nozzle Size: 0.4mm
s: No
Infill: 15% Grid
Ironing: Optional, but I iron all top surfaces, using spacing 0.2mm (gives a beautiful smooth finish)