RAINBOW SIX SIEGE (PROXIMITY ALARM - PROXIMITY ALARM)

English:

Hello everyone, I bring you a model of the proximity alarm used by the defenders in the game Rainbow Six Siege.

This model can be printed just as a decorative object, or if you want you can make the circuit to make it perform the effect of the real gadget.

AS A DECORATIVE OBJECT:

The following needs to be printed:

1 x Inf Housing

1 x Upper Housing

3 x Rubber Lat

3 x Rubber Sup

3 x Inf Foot

3 x LED Holder

1 x Grille

1 x Power Button Holder

1 x Power Button

REMARK:

In case you can't get the small metal grid, I've left a printable file that can make up for it:

Metal Grid SUPPLEMENT.STL

The following need to be purchased:

1 x Small metal grid

6 x Screw M3x20mm

6 x M3x8mm screw

12 x Hex nut M3

8 x Screw M2.5x5mm

AS GADGET:

In addition to the above mentioned, the following must be purchased:

1 x Arduino nano

1 x 9V battery

1 x PIR sensor for Arduino

1 x Active Buzzer

3 x 3mm Blue Led.

1 x Push button switch

1 x 9V battery holder

3 x Neodymium Magnet 20x10x2mm

3 x 1K resistor

The instructions are inside the attached "Instructions.txt" file.

The programming of the Arduino is inside the file "Arduino_CODE.txt".

I leave you a video of a part of the assembly since my computer was damaged and I lost the rest of the videos of the assembly.

https://www.youtube.com/watch?v=slQ2mGdfy7c

I leave you from the demo video:

https://www.youtube.com/watch?v=hPwaOsx1gvI

English:

Hello everyone, I bring you a model of the proximity alarm that defenders use in the Rainbow Six Siege game.

This model can be printed only as a decorative object, or if you want you can make the circuit to make the effect of the real gadget.

AS A DECORATIVE OBJECT:

The following needs to be printed:

1 x Inf Housing

1 x Upper Housing

3 x Rubber Lat

3 x Rubber Sup

3 x Inf Foot

3 x LED Holder

1 x Grille

1 x Power Button Holder

1 x Power Button

You need to buy the following:

1 x Small metal grill

6 x M3x20mm Screw

6 x M3x8mm Screw

12 x M3 hex nut

8 x M2.5x5mm Screw

NOTE:

In case you cannot get the small metal grid, I have left a printable file that can replace it:

Metal Grid SUPLENTE.STL

AS GADGET:

In addition to the above mentioned, you must buy the following:

1 x Arduino nano

1 x 9V Battery

1 x PIR Sensor for Arduino

1 x Active Buzzer

3 x 3mm Blue Led.

1 x push-button switch

1 x 9V battery holder

3 x 20x10x2mm Neodymium Magnet

3 x 1K resistor

The instructions are inside the file "Instructions.txt" that is attached.

The Arduino programming is inside the "Arduino_CODE.txt" file.

I'm leaving you a video of part of the assembly since my computer broke down and I lost the rest of the assembly videos.

https://www.youtube.com/watch?v=slQ2mGdfy7c

I leave the demonstration video:

https://www.youtube.com/watch?v=hPwaOsx1gvI

English:

The following parts should be printed on TPU or TPE:

Lat.STL rubber

Leg Inf.STL

The following parts can be printed in PLA, PLA+, PETG, ABS or any other non-flexible filament:

Inf.STL housing

Housing Sup.STL

Rubber Sup.STL

Grid.STL

Power Button Holder.STL

Power Button.STL

The following part should be printed in any translucent filament:

LED Holder.STL

English:

The following parts must be printed on TPU or TPE:

Rubber Lat.STL

Leg Inf.STL

The following pieces can be printed in PLA, PLA +, PETG, ABS or any other non-flexible filament:

Inf.STL housing

Housing Sup.STL

Rubber Sup.STL

Grid.STL

Power Button Holder.STL

Power Button.STL

The following piece must be printed on any translucent filament:

Porta Leds.STL