Skip to content

Minecraft Redstone Raspberry Pi Case

Advertising
Share
Add to
Make
Advertising
?
Creation quality: 5/5 (3 votes)
Evaluation of on the printability, utility, level of detail, etc.
License
Usages
3D design format
16 files (STL) Close
  • RedStoneBlock01-30FanClip.stl
  • RedStoneBlock01-40FanClip.stl
  • RedStoneBlock01-Base-1-Tab-Replacement.stl
  • RedStoneBlock01-Base-2-Tab-Replacement.stl
  • RedStoneBlock01-Base-3-Tab-Replacement.stl
  • RedStoneBlock01-Base-4-Tab-Replacement.stl
  • RedStoneBlock01-Base-5-Tab-Replacement.stl
  • RedStoneBlock01-Base-6-Tab-Replacement.stl
  • RedStoneBlock01-Base-CableTab.stl
  • RedStoneBlock01-Base.stl
  • RedStoneBlock01-BoardMount.stl
  • RedStoneBlock01-Clip.stl
  • RedStoneBlock01-Diff.stl
  • RedStoneBlock01-FanMount.stl
  • RedStoneBlock01-LEDClip.stl
  • RedStoneBlock01-Side.stl

Learn more about the formats
Last update 2023-10-26 at 04:42
Publication date 2023-10-13 at 03:52
Design number 1511080
ozylot

ozylot

Certified
Issue with this design? Report a problem.

2 comments

Add a comment

2 comments

Surtrofthe9realms
Surtrofthe9realms

I have a question. are there any instructions for how to put this together. my dad tried to print this and is kinda fumbled as to how this is put together, we tried putting the little pieces in the square holes in the red sections but they don't fit

thank you

ozylot
ozylot

I don't really have any instructions put together at this time other than the attached pictures on the page. I printed the clips out of PLA and they just snapped in with a small amount of force. If a brim was used is it possible that some excess material may need to be sanded or trimmed away?
ripienaar
ripienaar

Lovely looking case, I tried it for a PI5 and I just dont see how a pi5 with its micro hdmi+usb-c power+usb keyb cable can fit in here. Standing orientated as per the photos here the cable does not fit in the case, without the stand there's no orientation that has enough clearance for the hdmi cable+usb cables they add too much bulk due to the hard plastic around the plugs.

ozylot
ozylot

The stand with the tabs is essential for adding that extra clearance for the usb ports underneath. As for the sides, I have noticed that some cables that have a larger amount of shielding near the plugs are not ideal.

I haven't tested it yet, but the side s and clips could be scaled up 5-10% and that might just be the clearance needed.

ozylot
ozylot

So, scaling the 5 outer s and diffs to 120% will add an extra 1 cm of clearance inside if you are using a cable with a longer bit of hard plastic near the end. The cube will sit a bit lower on the stand but should still work. In cura, I needed to use a setting that fills gaps between walls when I scaled up the diffs.
Let me know how it goes and I will make some updates if needed.

Would you like to Cults?

You like Cults and you want to help us continue the adventure independently? Please note that we are a small team of 4 people, therefore it is very simple to us to maintain the activity and create future developments. Here are 3 solutions accessible to all:

  • ADVERTISING: Disable your ad blocker.
  • DONATE: Make a donation via Ko-Fi πŸ’œ.
  • WORD OF MOUTH: Invite your friends to come, discover the platform and the magnificent 3D files shared by the community!

Sharing and ing on Cults3D guarantees that designs remain in makers community hands! And not in the hands of the 3D printing or software giants who own the competing platforms and exploit the designs for their own commercial interests.

Cults3D is an independent, self-financed site that is not able to any investor or brand. Almost all of the site’s revenues are paid back to the platform’s makers. The content published on the site serves only the interests of its authors and not those of 3D printer brands who also wish to control the 3D modeling market.